TSHOOT – Troubleshooting Spanning-Tree and Layer 2 EtherChannel issues!

Above is a simple STP topology from earlier SWITCH labbing, however this will cover all STP flavors (PVST+ / RSTP / MSTP), features that go with them, and EtherChannels. STP issues, how to identify and resolve them, and feature behaviors In relation to the TSHOOT exam, the most important thing to note is that the … Continue reading TSHOOT – Troubleshooting Spanning-Tree and Layer 2 EtherChannel issues!

STP – Multiple Spanning-Tree (MST), CST, PVST vs PVST+ reviewed, illustrated, configured and verified on the lab!

The above Topology is configured waaaay toward the bottom of the post, there is a lot of ground to cover in terms of the evolution of STP, and clarifying some differences in flavors. I have spent days researching Cisco documentation / Blogs / Discussions / Training material to cross reference MST information, as this is … Continue reading STP – Multiple Spanning-Tree (MST), CST, PVST vs PVST+ reviewed, illustrated, configured and verified on the lab!

STP – Fiber Cabling, Loop Guard and UDLD DEEP DIVE, and important notes for exam day!

The above Topology represents a failure on a Fiber Optic Transmit / Receive cable pair on one cable, on one end of the link, which would leave the link up and Unidirectional. Here is an example of the SFP Transceiver and Fiber cable connecting to a switch: Source : This Cisco.com 2960x Fiber Stacking article … Continue reading STP – Fiber Cabling, Loop Guard and UDLD DEEP DIVE, and important notes for exam day!

STP – Root Guard, BPDU Guard, and BPDU Filter mechanics, behaviors, and verification labbed!

In this Topology everything is default, so SW1 has one the Root Bridge election with the lowest MAC Address as the tie breaker, and all port states were dynamically calculated. There is a lot to hit on these multiple STP topics, so, without further ado!   First a quick peek at a great verification command … Continue reading STP – Root Guard, BPDU Guard, and BPDU Filter mechanics, behaviors, and verification labbed!

STP – Configuring and verifying Root Bridge, behaviors from configs, Priority configruation + sys-id-ext labbed!

For this lab I will be using the STP Topology with the default link states shown above, however I have reduced the additional VLANs to 10 / 20 / 30, to generate less output when comparing STP behaviors from changing the Root Bridge on specific VLANs. SW1 will be made the Root Bridge for VLAN … Continue reading STP – Configuring and verifying Root Bridge, behaviors from configs, Priority configruation + sys-id-ext labbed!

STP – Root / Designated / Blocking Port selection process, illustrated for both equal and unequal STP Cost diagrams!

Consider the above Topology running STP with default settings, with 6 additional VLANs to the default Native VLAN 1, which links will be in what status by default?   Equal Cost link speeds in a default STP Port Selection process   First lets review the Root Port default election criteria once more: Port that receives … Continue reading STP – Root / Designated / Blocking Port selection process, illustrated for both equal and unequal STP Cost diagrams!

STP Timers – Aging Time value, defaults covered, important exam day root vs non-root behaviors labbed!

Boring repeat of the same old Topology, but works perfectly for review, so lets do it! To review the STP timers the command "show span vlan #" is used depending on which VLAN you are looking for, in this case it is VLAN 30 throughout this lab: SW2#sh span vlan 30 VLAN0030 Spanning tree enabled … Continue reading STP Timers – Aging Time value, defaults covered, important exam day root vs non-root behaviors labbed!

STP – Interface Cost config, VLAN load balancing with PVST and Port Priority, and verification commands labbed!

Above is a design issue that may be present on exam day or on the job, the issue being that as indicated in the top right corner there are 4 VLANs configured on both sides of the Trunks, but SW2 has interface Fa1/0/2 set to blocking - So only one link is being used for … Continue reading STP – Interface Cost config, VLAN load balancing with PVST and Port Priority, and verification commands labbed!

STP – Path cost info, identifying the Root Bridge, Root Cost vs Path Cost, and debugging STP port state transitions!

Most of this demonstration will be on the above Topology, except for the the output for changing Port cost, for that I'll just be using 2 Trunk links between SW1 and SW2.   STP Link Speed to Path Cost, and how to change Path cost on an interface   The link speed to STP cost … Continue reading STP – Path cost info, identifying the Root Bridge, Root Cost vs Path Cost, and debugging STP port state transitions!